Before you order

  1. Measure the cut-outWidth and height of the hole, the corner radius, and the panel or door thickness. Note the depth behind the panel and anything nearby that limits it.
  2. Record the mountingPanel mount with clamps, VESA 75 or 100, an arm, a pedestal or a bracket. Photograph how the old product is held.
  3. List every connectionEthernet ports, fieldbus, serial (RS232, RS422, RS485), CAN, USB devices, digital I/O and video. Note the connector type at the cable end.
  4. Check the powerThe supply voltage and type at the cabinet, its spare capacity, and whether a UPS or safe shutdown is needed.
  5. Check the softwareThe operating system, the HMI runtime and its licence, the drivers, and the resolution the screens were drawn for.

The cut-out and the mounting

The easiest change is a product that fits the existing hole. STX Technology panel-mount products run from 10.1" to 24" on the X5200 and X7700 and 8.4" to 27" on the X7600, X7200 and X7300, so one of them is usually close; if no size fits exactly, an adaptor plate covers a larger hole, while a smaller hole means cutting the panel, which in a stainless washdown area also means re-finishing the edge. Check the bezel overlap as well as the hole, so the gasket seats on flat panel all the way round.

Panel-mount clamps differ between makers, so plan for the new product's clamps and the depth they need behind the panel. For an arm, pedestal or wall bracket, compare the weight and the VESA pattern: STX Technology products take VESA 100, the X7000 and X9000 mount on M10 side bolts with VESA 100 as an option, and the XRH7000 uses a RAM ball on VESA 75. Send the measurements with your enquiry and the team confirms the fit before the quote.

Connections and power

Match the protocols first and the connectors second. A fieldbus or serial link the HMI depends on must be on the new product or added as an option; a connector style can usually be changed with a new cable. STX Technology products offer up to 3 × Ethernet 1000 Mbps, up to 8 × RS232, RS422 / RS485, CAN bus and high-speed serial to 3 Mbaud, with M12 automation connectors in place of RJ45, USB and DB9 on the HMI and thin-client products. In washdown areas, use the IP67 / IP68 connectors (NEMA 6 equivalent) and cap the unused ones.

Control cabinets usually supply 24 V DC. The X7500, X7000, X9000, X7600, X7200, X7300, X7700 and X5200 take 10–30 V DC, so a 24 V supply drives them directly, the large-format 32" to 55" products included; the XRH7000 takes 8–36 V DC vehicle power. Check the product's draw against the spare capacity of the cabinet supply, and ask for the power option your cabinet already has rather than adding a converter.

Software

Some HMI runtimes are licensed to the maker's own hardware. Ask the software vendor whether your licence moves to new hardware before you plan the change; a runtime that is tied to a controller brand may need a monitor-only replacement instead, with the old controller kept. If the new screen has a different resolution or aspect ratio, the HMI screens may need scaling or redrawing, so matching the old resolution avoids that work: STX Technology sizes come in 4:3, 5:4, 16:9 and 16:10.

STX Technology computers are offered with Windows 11 IoT Enterprise LTSC, Windows 11 Pro, Windows 10 IoT Enterprise LTSC, Linux (Mint 22, Ubuntu 20.04, 22.04 or 24.04) or Android 13 on the ARM option, with network boot (PXE) and TPM 2.0 as standard, so a thin-client or ThinManager site keeps its set-up. Where the old computer stays, the same product is offered as a touch monitor, or as a KVM monitor that carries video and touch up to 100 m over one CAT6 cable.

STX Technology model match list

Which STX Technology model and size replaces each common Beckhoff and Siemens panel PC, with cut-out sizes: to supply from STX Technology.

Quick answers

Will the new product fit my existing cut-out?

Send the width, height, corner radius and panel thickness. Sixteen sizes from 8.4" to 55" cover most holes; where none fits exactly, an adaptor plate covers a larger hole.

Can I keep my existing controller and change only the screen?

Yes. Every range is offered as a touch monitor (HDMI, DVI, VGA or DisplayPort in; USB or RS232 touch) or as a KVM monitor up to 100 m from the computer over one CAT6 cable.

Does it run on my 24 V cabinet supply?

Every range takes 10–30 V DC, so yes; check the draw against your supply's spare capacity. @related Industrial panel PCs=/family-panel-pc ;; Choosing a screen size=/guide/size ;; Panel PC, or a touch monitor and KVM?=/guide/form ;; Power supplies=/acc-power ;; Compare sizes=/compare